Welcome to the WRR/X Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.
Welcome to the WRR/X Forum

A place to share your passion for the WR250R/X!
 
HomeHome  Latest imagesLatest images  SearchSearch  RegisterRegister  Log inLog in  
WR250R/X Forum

 

 how to access the tps screws

Go down 
2 posters
AuthorMessage
michiko





how to access the tps screws Empty
PostSubject: how to access the tps screws   how to access the tps screws EmptySat Aug 01, 2015 6:13 pm

How the hell, do you access the the screws for the throttle response sensor? do i have to remove the the throttle body?
Back to top Go down
Jens Eskildsen





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws EmptySun Aug 02, 2015 5:37 am

I removed seat and sidepanel, and used a hammer and a punch to "adjust" it, witgout loosening the bolts Shog
Back to top Go down
michiko





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws EmptySun Aug 02, 2015 6:00 am

no seriously. where exactly did you rest the punch against.
Back to top Go down
Jens Eskildsen





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws EmptySun Aug 02, 2015 12:14 pm

Are you able to find the tps? Its on the right side of the bike, behind the frame.

I have no pictures showing it, and its been some time since I messed with it.

Its held on with 2 screws. I went in to diagnostic mode on the display, to show current position, and then gave it some tabs sideways, and confirming movement on the display. I stopped when max was at about 98 or 99%.

Theres a guide here: https://wr250rforum.forumotion.com/t5568-throttle-on-off-at-idle
Back to top Go down
michiko





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws EmptyTue Aug 04, 2015 12:10 am

i did try to budge it but it didnt move and i was scared to hit it too hard. it looks really flimsy. how hard did you hit it?
Back to top Go down
Jens Eskildsen





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws EmptyTue Aug 04, 2015 4:18 am

Just about enough to move it, I've never heard about anyone braking it...

But theres still a guide to show you how to unbolt it properly, it just seemed like too much work for me.


Last edited by Jens Eskildsen on Wed Aug 05, 2015 1:55 pm; edited 1 time in total
Back to top Go down
michiko





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws EmptyWed Aug 05, 2015 8:10 am

okay after hitting it and trying to gain access to it for hours. ive got it reading 18 97. which contrary to what has been written both figures did not change simultaneously.
Back to top Go down
Sponsored content





how to access the tps screws Empty
PostSubject: Re: how to access the tps screws   how to access the tps screws Empty

Back to top Go down
 
how to access the tps screws
Back to top 
Page 1 of 1
 Similar topics
-
» OHV access- this isn't going to help
» Any advice on getting access to TPS?????
» Active Thread Easy Access
» IMS 3 GALLON TALLY!
» 2 black hex screws . . . where from?

Permissions in this forum:You cannot reply to topics in this forum
Welcome to the WRR/X Forum :: Technical :: General Maintenance Discussion-
Jump to: