Welcome to the WRR/X Forum

A place to share your passion for the WR250R/X!
 
HomeHome  CalendarCalendar  FAQFAQ  SearchSearch  MemberlistMemberlist  UsergroupsUsergroups  RegisterRegister  Log inLog in  
WR250R/X Forum

Share | 
 

 need bars

View previous topic View next topic Go down 
AuthorMessage
mucker

avatar


PostSubject: need bars   Fri May 06, 2011 11:02 pm

Well I've been a little hard on 'er.
Need some new bars.
7/8 renthals are bout $90.
Another shop had generic bars for $40, similar looking.

Question: Cheap bars should be good, eh?...

Next question: Whats the difference between CR bend and KX bend?

Third question: Any advice?


.........Thanks

Back to top Go down
0007onWR

avatar


PostSubject: Re: need bars   Sat May 07, 2011 12:24 am

I always say, cheep stuff costs less
They will bend easier but hey, if yer just looking for replacements get the cheeps and quit falling down :)
Back to top Go down
KLRchickie




PostSubject: Re: need bars   Sat May 07, 2011 12:50 am

Just to give the opposite opinion - I'm happy to spring for Renthals in a bend I like & know that I have a good chance of surviving a crash without bending the bars!
Back to top Go down
greer




PostSubject: Re: need bars   Sat May 07, 2011 6:18 am

Here's a chart:

http://www.rockymountainatvmc.com/handlebarinfo.do

Sarah
Back to top Go down
47une

avatar


PostSubject: Re: need bars   Sat May 07, 2011 6:43 am

I just purchased some Tag Metal bars in a "YZ double bend" hopeing they are high enough to not need bar raisers and hoping the YZ bend suits me....... they were cheap enough though at $29 AUD.
Back to top Go down
mucker

avatar


PostSubject: Re: need bars   Sat May 07, 2011 9:07 am

Thanks for the replies.

Guess I shouldn't consider pricier bars till I proof responsible enough to care for a cheap set...may take a little while Very happy

...I also want to ask which bend is stock or nearest to? Stock seems comfortable so far.


Back to top Go down
Akasy




PostSubject: Bars   Sat May 07, 2011 9:24 am

I've found the best way is go to a store that has a selection and take your stock bars or the ones you are trying to match and compare. Bend, rise etc are all important but don't forget width. If the replacement set is wider--even by only a couple of inches it could impact your cable slack. I've trimmed a lot of aftermarket bars to get them to where I want them for my use. One thing I don't do is go to compare bars at the local brick and mortar store them order on line--I give my business to the store that has them there for me to look at and compare. Take a picutre of your cable routing before removing the stock ones--makes it easier.
Back to top Go down
SheWolf
Alpha Rider
avatar


PostSubject: Re: need bars   Sat May 07, 2011 11:31 am

I've got the Renthal McGrath bend which is close to stock, but isn't bang on stock bend. thumb

_________________
A wolf's voice echoed down the mountain 'Share the bounty of the hunt with your brothers and sisters, and forever be strong and free.'
Back to top Go down
spacecadet




PostSubject: Re: need bars   Tue May 17, 2011 10:07 am

you can get some oversized eastons *various bends* and oversized clamps right now for ~90$ from http://www.motorcycle-superstore.com/
Back to top Go down
Sponsored content




PostSubject: Re: need bars   

Back to top Go down
 
need bars
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» crash bars for k100rt
» Anti-vibration bars
» Lakewood ladder bars
» Custom Tranny Hanger and ladder bars system
» Ford focus roof bars for sale

Permissions in this forum:You cannot reply to topics in this forum
Welcome to the WRR/X Forum :: Technical :: General Maintenance Discussion-
Jump to: