| Welcome to the WRR/X Forum A place to share your passion for the WR250R/X! |
| | Check engine after exhaust change | |
| | Author | Message |
---|
shamen
| Subject: Check engine after exhaust change Wed Aug 03, 2016 12:20 pm | |
| Hey, I have changed on my WR the stock exhaust with FMF POWER BOMB 4, and the check engine get on and off.... I know that its a know issue after changing the exhaust, is there any thing to do to solved it?
Thanks Nicolas | |
| | | YZEtc
| Subject: Re: Check engine after exhaust change Wed Aug 03, 2016 7:48 pm | |
| Did you unplug the EXUP servo motor? | |
| | | shamen
| Subject: Re: Check engine after exhaust change Thu Aug 04, 2016 2:58 am | |
| | |
| | | YZEtc
| Subject: Re: Check engine after exhaust change Thu Aug 04, 2016 6:17 am | |
| That's the cause. The missing servo motor is causing the warning light.
You can:
1) Mount and plug the servo motor back in (without the control cables in place). 2) Buy one of the servo eliminators on the market and plug that in. 3) Try the modification that uses a small resistor to do what the servo eliminator does. 4) Run it as-is. | |
| | | shamen
| Subject: Re: Check engine after exhaust change Thu Aug 04, 2016 6:53 am | |
| | |
| | | shamen
| Subject: Re: Check engine after exhaust change Wed Sep 14, 2016 10:39 am | |
| I've check and I have a servo eliminator, but still sometimes the check engine get on. It might be that the servo device isn't working properly? There is nothing written on it so I don't know what is his brand, should I buy another one and change it? If yes what brand is the most recommended?
Thanks | |
| | | Jens Eskildsen
| Subject: Re: Check engine after exhaust change Wed Sep 14, 2016 1:08 pm | |
| Check the faultcode(s) to see whats actually throwing a code..
https://www.youtube.com/watch?v=HL6mbSmQnXQ | |
| | | johnkol
| Subject: Re: Check engine after exhaust change Wed Sep 14, 2016 1:51 pm | |
| - shamen wrote:
There is nothing written on it so I don't know what is his brand, should I buy another one and change it? If yes what brand is the most recommended?
- YZEtc wrote:
3) Try the modification that uses a small resistor to do what the servo eliminator does.
Solution (3) is a sticky right here on this site: https://wr250rforum.forumotion.com/t627-cheapest-diy-servo-bypassIt's simple, cheap, and it works; I used a 10k, 1/4W resistor. | |
| | | shamen
| Subject: Re: Check engine after exhaust change Sat Oct 15, 2016 9:27 am | |
| Hey, Finally I have checked the codes. Those are the codes: 17 18 21 30 33 42
Also my battery shows 11.2 is that OK? Thanks | |
| | | Jens Eskildsen
| Subject: Re: Check engine after exhaust change Sun Oct 16, 2016 6:10 am | |
| 11.2v is totaltally discharged, so no. But it should recover fine when fully charged. | |
| | | shamen
| Subject: Re: Check engine after exhaust change Sun Oct 16, 2016 6:56 am | |
| what about the other error codes? are they ok? | |
| | | Jens Eskildsen
| Subject: Re: Check engine after exhaust change Sun Oct 16, 2016 1:14 pm | |
| Hi, perhaps this can help you:
http://www.cyclepedia.com/manuals/online/cpp-203/fuel-system/fail-safe-system/
See if you cant clear them. | |
| | | Sponsored content
| Subject: Re: Check engine after exhaust change | |
| |
| | | | Check engine after exhaust change | |
|
Similar topics | |
|
| Permissions in this forum: | You cannot reply to topics in this forum
| |
| |
| |
|